LG APPLIANCE REPAIR Factory Authorized Service · Irvine, CA

LG Dishwasher Not Cleaning? Causes & How to Fix It

Dishes come out with food stuck on, a gritty or white film, or glasses that look cloudy. Sometimes the machine barely fills, or the display won't light at all.

Call (949) 876-7373 Text Us
✅ Factory Authorized LG Service Provider 🛡️ Licensed & Insured ⚡ Same-Day Appointments 🔧 90-Day Parts & Labor Warranty
LG Dishwasher Not Cleaning

Try these quick checks first (free & safe)

  1. Before you start a cycle, run the hot water at the kitchen sink until it's hot. The dishwasher's first fill should be hot, not the cold water sitting in the pipe.
  2. Twist out the filter at the bottom of the tub and rinse it. Pop off the spray arms and clear the small holes with a toothpick.
  3. Load so nothing blocks the arms: tall pans and cutting boards go along the sides, bowls face down and toward the center.
  4. Use dishwasher detergent and keep the rinse aid dispenser filled. Rinse aid is what keeps glasses from spotting.
  5. If it won't fill or won't start, check that the valve under the sink is fully open, the door is latched, child lock is off and delay start isn't set.

What actually causes it, from LG technicians

Cold water at the start

Detergent works poorly in cold water. The supply should be on the hot line and arrive around 120°F, not above 140°F. A long pipe run from the water heater or a dishwasher plumbed to the cold line is a common reason for dirty dishes.

Clogged filter or spray arms

Food and hard-water scale close up the filter and the spray arm holes. Water still circulates, just weakly and not where it needs to go.

Not enough water coming in

A partly closed valve, a kinked hose, or a calcium-clogged screen at the inlet valve starves the machine. Water pressure below about 20 psi or above 120 psi is a plumbing problem the dishwasher can't work around.

Inlet valve or flow meter fault

The board counts water with a small flow meter. If the meter's wheel sticks or its signal drops out, the fill is wrong. A failed inlet valve gives you little or no water and an IE code.

Heater or temperature sensor

If the heater or its thermistor fails, the wash water never gets hot and the drying is poor too. These usually show up as HE or tE.

Circulation motor weak

A worn circulation pump moves less water through the arms. It's often noisy as well, and can throw an LE code.

What it looks like

Related LG error codes

CodeMeaning
IEWater inlet error: not enough water came in
HEHeater error: wash water isn't heating
tEThermistor error: temperature sensor fault
LEMotor error: circulation motor locked or not turning properly

Full LG error code reference →

How we diagnose it on a service call

How you use it matters, so we ask first

We start with questions: which cycle, which detergent, whether rinse aid is used, any codes lately. A lot of not-cleaning calls come down to loading and water temperature, and it's better to find that out in two minutes than replace a part that wasn't bad.

Water temperature with a probe

We put the machine in test mode, run only the fill step until water covers the bottom of the tub, and measure it with a temperature probe on the meter. Around 120°F is right. Lukewarm water tells us the problem is the plumbing or the heater, not the pump.

Checking the fill

With the supply off we take the hose off the inlet valve and look at the screen for scale. Then we measure the valve. Depending on the model it's either a 120V AC valve reading roughly 900 to 1,300 ohms, or a low-voltage DC valve around 8 to 12V and 20 to 30 ohms. If the valve gets voltage and doesn't open, the valve is bad. If the board never sends voltage, it's the board or the harness.

Flow meter signal

If water comes in but the count is wrong, we check that the flow meter's wheel turns freely, that the board is sending it 5V DC, and that it pulses back a signal while water flows. No pulse with power present means a bad flow meter.

No power or dead display

We confirm 120V at the outlet or junction box, then through the noise filter board into the main board, and check the main board's status LED. If the main board is alive, we measure the low-voltage feed to the display board (about 12V DC on older models, 16.5V DC on newer ones). Voltage there with a dark display means the display board. No voltage means the main board or the harness between them.

🔧 When it's time to call a pro

We see a lot of LG dishwashers that are mechanically fine and just need a clean filter, clear spray arms and hot water at the first fill. We check those first and tell you straight. When it is a part, it's usually the inlet valve, the heater circuit or the circulation pump, and we confirm it with readings before ordering anything.

LG Dishwasher Not Cleaning: FAQ

Why are my dishes still dirty after a full cycle?+

Most often it's a clogged filter, blocked spray arm holes, or cold water at the start of the cycle. If those check out, we look at the fill, the heater and the circulation pump.

Why is there a white film on my glasses?+

Hard water and no rinse aid are the usual cause in Orange County. Keep the rinse aid filled and clean the filter and arms regularly. A film that keeps getting worse can also mean the water isn't heating.

My LG dishwasher won't fill with water. What should I check?+

Make sure the valve under the sink is fully open and the hose behind the unit isn't kinked. If both are fine, the inlet screen may be clogged with scale or the inlet valve or flow meter has failed, which is a technician job.

Related LG repairs

🍽️ LG Dishwasher Not Draining → 🔊 LG Dishwasher Making Noise → 💧 LG Dishwasher Leaking →

LG Dishwasher Not Cleaning, service in your city

Aliso Viejo Anaheim Brea Buena Park Costa Mesa Cypress Dana Point Fountain Valley Fullerton Garden Grove Huntington Beach Irvine La Habra La Palma Laguna Beach Laguna Hills Laguna Niguel Laguna Woods Lake Forest Los Alamitos Mission Viejo Newport Beach Orange Placentia Rancho Santa Margarita San Clemente San Juan Capistrano Santa Ana Seal Beach Stanton Tustin Villa Park Westminster Yorba Linda

Fix Your LG Dishwasher Not Cleaning Today

Factory authorized LG repair, parts on the van, 90-day warranty. Same-day across Orange County.

Call (949) 876-7373 Text Us
⚡ $25 OFF For new & referred customers