The dryer gets warm and runs the full cycle, but the clothes are still damp at the end, or a normal load takes two hours. Heat pump dryers and WashTower or combo units just keep running.

By far the most common cause. Lint in the screen housing, a crushed foil duct behind the dryer, or years of lint in the wall vent. The dryer heats fine, but the moist air can't get out. A blocked vent also raises the temperature at the back of the drum, and can scorch clothes or discolor the rear vent grill.
The sensor bars tell the control when the clothes are dry. Coated with softener residue they read dry too soon and the cycle ends with damp clothes. A broken wire or a bad connection at the board does the same.
Energy Saver, Air Dry, a low dry level or a timed cycle that's too short all leave clothes damp. On the other side, Very Dry on every load makes dry times long.
Heat pump dryers dry with a small refrigeration system instead of a heating element. They're slower by design, but if the compressor isn't building heat or the system has lost refrigerant, dry times stretch to several hours. This is EPA-certified technician work.
On the WM6998 WashCombo, lint collects in the drum vent and the duct bellows. LG released a redesigned lint filter, a finer magnetic condenser filter, and an updated vent and dispenser to cut lint buildup. If the drum vent ducting isn't seated correctly, drying suffers too.
If a natural gas dryer was switched to LP without the right orifice, the flame runs wrong and you get uneven heat, scorched clothes and odd dry times.




| Code | Meaning |
|---|---|
d80 / d90 / d95 | Exhaust duct about 80 to 95 percent blocked (Flow Sense), clean the vent line |
tE1 / tE2 / tE3 | Temperature sensor (thermistor) fault |
We pull the dryer out, inspect the transition duct and measure how freely air leaves the outside vent hood. If Flow Sense is showing bars or a d80 to d95 code, the vent is the problem and replacing parts won't help. We also look at the rear bulkhead grill: a brown, discolored grill tells us the dryer has been running hot from a restriction.
In the service test mode the display shows the sensor reading. We touch a damp cloth across the bars and watch the number. Wet laundry reads under about 130, damp dry sits around 130 to 205, and fully dry reads above about 205. If the number doesn't move, we trace the harness back to the main board and measure the voltage on the sensor line.
On heat pump models we let the unit run at least 10 minutes and read the compressor discharge temperature in the data view mode. It should climb clearly from its starting value as the system builds heat. We then clamp an amp meter on the compressor lead: a healthy draw is above roughly 0.2 amps, while a reading under about 0.1 amps points to a refrigerant leak.
LG heat pump dryers don't get a refrigerant top-off. If the compressor or the sealed system has failed, the whole heat pump assembly is replaced as a unit. We confirm the diagnosis before that is ordered and check whether your model and serial still have coverage.
If your LG dryer gets hot but leaves clothes damp, it's not the same problem as a dryer that won't heat. Most of the time we're looking at the vent, the sensor bars or a setting, and the dryer itself is fine. Heat pump and WashCombo units are slower by nature, so we check whether the dry time is actually abnormal for that design before we touch anything.
Heat without drying almost always means airflow. Moist air can't leave through a clogged lint screen, crushed duct or blocked wall vent. Dirty moisture sensor bars and the Energy Saver setting are the next things to check.
Heat pump dryers run at lower temperatures and take longer than vented dryers, that's normal. If it suddenly gets much slower, clean all the filters first. If that doesn't help, the heat pump system may have a problem and needs a technician to measure it.
The lint screen after every load, and the vent line to the outside about once a year, more often for long duct runs or a big household. A clean vent also lowers fire risk and stops the dryer from overheating.
Factory authorized LG repair, parts on the van, 90-day warranty. Same-day across Orange County.