The oven heats, but recipes come out wrong: underdone centers, burned bottoms, one side darker than the other, or air fry that never gets crispy. Some owners also see a dim, unresponsive display or a door that stays locked.

An oven that runs 10 to 25°F cold undercooks everything. Sensors drift and settings get reset. LG lets you adjust the oven offset from the settings menu, but only after the real temperature has been measured properly.
If the sensor reads wrong, the control holds the wrong temperature. A sensor out of range usually shows as an F3 or F4 code, a drifting one just bakes badly.
On convection and air fry settings a dead fan means hot and cold spots and no crisping. Note that the fan icon on the display spins whether the fan is turning or not, and on many models the fan cycles on and off during air fry by design.
A bent hinge or worn gasket lets heat escape at the top of the door, so the front of the oven runs cool and the knobs and handle get hotter than they should.
A display with missing segments, buttons that don't respond, or a dead panel can be a loose connector, the LED module, or the display or main board.
A lock that won't release after self-clean, won't engage, or throws F10 points at the lock motor, its switch, or the oven thermostat that cuts power after overheating.




| Code | Meaning |
|---|---|
F10 | Door lock fault: lock motor or lock switch not responding |
F3 / F4 | Oven temperature sensor open or shorted |
Oven thermometers that hang on the rack are slow and often wrong. We preheat to 400°F for at least 20 minutes, then put a thermocouple probe in the center of the middle rack with a folded bead of foil around the tip, which acts as a small load and evens out the swings. We skip the first high and low, average the highs and lows of the next three heating cycles, and that average is the true oven temperature.
If the average is, say, 394°F at a 400°F setting, we enter a +6°F adjustment in the settings menu (ADJ on single ovens, U-AJ and L-AJ for the upper and lower cavities on doubles) and recheck. If the error is large or changes from day to day, we test the sensor resistance and replace it rather than hide the problem with an offset.
Instead of watching the icon we run the oven in test mode on the convection fan step, where the board has to power the fan. Fan turns: it's working, and an on-off pattern during a normal air fry cycle is normal for that model. Fan doesn't turn: we measure voltage at the fan in that test step and the motor's resistance to tell a bad motor from a bad board or wire.
Dead panel: we check 120V from each leg to neutral and 240V across at the supply and terminal block, then 120V into the power board, then the connection from the main board to the display. Dim or missing segments: we reseat the LED module connector and replace the module if needed.
We check the lock switch (normally open) and the lock motor resistance, which should be around 2,600 ohms. An open reading or almost zero means a bad motor. If the whole range went dead right after a self-clean, we check the oven thermal cutoff first, because that is what usually opens.
Before we sell anyone a part for uneven baking, we measure the oven properly. Many of these calls end with a calibration adjustment and some advice about racks and pans. When it is a part, it's usually the temperature sensor, the convection fan, or the door seal, and the readings tell us which one.
Usually a dark pan, a rack set too low, or an oven running hot. Try a shiny aluminum sheet on the middle rack. If it still burns, the oven temperature needs to be measured and the offset adjusted.
Not necessarily. The icon spins the whole cycle regardless of the fan, and many LG models cycle the fan on and off during air fry. We confirm it in test mode, and if the fan runs there, the oven is working as designed.
It's most likely standby mode, which kicks in after about five minutes of no use. Touch the screen, turn a knob or open the door to wake it. If it stays dark, that's a power or control board issue for a technician.
Factory authorized LG repair, parts on the van, 90-day warranty. Same-day across Orange County.