The washer bangs, knocks or grinds during spin, shakes hard enough to move across the floor, or the drum looks like it sits lower on one side.

Water eventually seeps past the seal and washes the grease out of the rear tub bearing. It starts with a hum during spin and turns into a loud roar or high-pitched grinding. On LG front loaders the bearing is pressed into the outer tub, so the fix is a major repair.
Front loaders hang on two top springs and three or four dampers underneath. A spring can pop off after a very light or very heavy load, and worn dampers let the tub sag and slam the cabinet. Top loaders hang on four suspension rods, and when one weakens, all four should be replaced.
The concrete weights on the outer tub are bolted on. If they loosen, you hear a heavy knock every turn and the washer runs off balance. If the bolt threads in the plastic tub are stripped, the tub and weights get replaced, not re-bolted.
The metal spider on the back of the drum holds it to the motor shaft. When an arm cracks, the drum sags, rubs the door boot and bangs during spin. It's often found together with a failed bearing.
On several WM3400 to WM4000 series models, the main control board cover can come loose and tap against the tub. A drain or fill hose that isn't clipped down can also slap the cabinet on spin.
A bang or shudder in the wall when the washer stops filling is the house plumbing reacting to the fast-closing valve. A gurgling fill can mean a clogged inlet screen or very high water pressure. A water hammer arrestor on the supply lines solves it.




| Code | Meaning |
|---|---|
UE / Ub | Unbalanced load, or a suspension or leveling problem if it keeps coming back |
CE | Motor overcurrent, can show when a dragging drum or seized bearing overloads the motor |
We run the service test mode and step through fill, wash motion, drain and spin one at a time. Noise only while draining sends us to the pump and its filter. Noise in spin with an empty drum means bearings, suspension or weights. A sound only at fill is the valves or the house plumbing.
With power off we turn the drum by hand and rock it up and down at the front. A healthy front loader turns smoothly with almost no up and down play. Grit or a clunk at the lip means bearing wear, and a drum that sits low or rubs the boot points at a spring, damper or cracked spider.
We push down on the tub several times to feel how it rebounds. On top loaders we also look at the plastic tub ring: if one side shows more gap, the tub isn't centered, so we level the cabinet first, then test each rod. Weak rods are replaced as a set of four so the tub doesn't pull to one side.
We torque-check the balance weight bolts and look for stripped threads, check that the board cover is fastened, and pull the rear cover to inspect the rotor and stator. If a rotor has seized onto the shaft from corrosion, we pull it with a proper puller instead of prying, so the shaft and motor aren't damaged.
A washer that walks across the floor is often just a leveling or loading issue, and we'll tell you so if that's all it is. A grinding roar on spin is different: that's bearings, and on LG front loaders it's a big repair, so we give you the honest numbers next to the price of a new machine before anything is ordered. Suspension springs and dampers are much smaller jobs and usually done in one visit.
The most common reasons are an uneven load, a washer that isn't level, worn suspension parts or a loose balance weight. If the banging happens with a normal mixed load and the washer is level, the suspension or weights need a technician.
Not for long. A grinding bearing gets worse quickly and can damage the shaft and the spider, which turns a bearing job into a much larger repair. Stop using it and have it checked.
Some tilt is normal when the tub is full, the springs compress under the weight. If it still sits crooked when empty, a suspension rod has likely stretched or come loose. We replace all four rods at once so the tub hangs evenly.
Factory authorized LG repair, parts on the van, 90-day warranty. Same-day across Orange County.