Most LG washer codes point to something you can check in a few minutes: a clogged pump filter, a closed faucet, a load bunched to one side. The list below covers LG front load washers, including WashTower units and washer and dryer combos. If a code keeps coming back after the simple checks, our factory authorized LG repair technicians can test the part behind it and fix it on the first visit in most cases.












| Code | Name | What the washer detected |
|---|---|---|
OE | Water not draining in time | The control watched the water level during drain and it did not drop fast enough. Something is slowing the water on its way out, or the pump is not moving it. |
IE | Not enough water coming in | The washer opened its fill valves but the water level barely changed in the time it expected. Usually the supply is weak or blocked, not the machine itself. |
UE | Load out of balance | The drum could not even out the clothes before high speed spin, so the washer stopped spinning to protect itself. It happens most with a single heavy item or a tiny load. |
Ub | Balancing in progress (info only) | Ub is an information message. The washer noticed an uneven load and is adding water and tumbling to fix it on its own. |
uS / u5 | Vibration sensor problem | The vibration sensor on top of the tub either sent a bad signal or recorded very hard shaking. On a WashTower the sensor sits under the dryer section. |
bU | Heavy vibration (WashTower) | This code shows on some WashTower models when the machine detects shaking far beyond normal. Causes range from a poorly leveled unit to a damaged inner drum. |
bE | Ball sensor (older models) | Only washers built around 2006 and earlier have this sensor. It tells the board the tub moved far enough to knock a small ball off its seat, and the board then tries to rebalance. |
LE | Motor cannot turn the drum | The board tried to spin the direct drive motor and the rotor did not move or the hall sensor did not report the movement. |
CE | Motor drawing too much current | The main board saw very high current on the motor circuit. Something is making the motor work far too hard or the motor itself has a fault. |
dE | Door not detected as closed | The board does not see the door switch circuit closed, so it will not lock the door or start. |
dE1 | Door switch circuit open | Same family as dE. The board is missing the signal that tells it the door is shut. |
dE2 | Door will not lock | The door closes but the lock never confirms it latched, so the cycle does not start. |
dE4 | Door sensor inside lock failed | The door position sensor built into the lock assembly is giving a reading the board does not trust. |
PE | Water level sensor fault | The pressure sensor that tells the board how much water is in the tub is reading open or shorted, so the washer cannot fill or drain correctly. |
FE | Too much water in the tub | The water level went above the safe limit. The washer will try to pump it out. |
tE | Water temperature sensor fault | The board reads the water thermistor as open or shorted, so it cannot control water heating. |
AE | Water in the base pan | On a regular front loader a float switch under the tub found water, so the washer stopped and runs the drain pump. On washer and dryer combo models with a heat pump AE means the compressor is locked. |
FF | Water or hoses frozen | The washer saw very cold water readings along with a fill, drain or overflow problem, which points to ice in the hoses, valves or pump. |
PF | Power was interrupted | The washer lost power while it was running. It is an information message, not a part failure. |
PS | Wrong supply voltage | The voltage coming into the washer is outside what it is rated for. Washers expect 120 volts, give or take about 10 percent. |
EE | Control memory fault | The memory chip on the main board failed its self check. |
Sud | Too many suds | The washer found too much foam. It adds a suds reducing routine, which can stretch the cycle by about two hours, and may stop the spin to keep suds from leaking out. |
CL | Child lock is on | CL is not a fault. Control lock is active, so every button except Power and the lock button is ignored. |
tCL | Tub Clean reminder (info only) | tCL is a reminder that the washer is due for its Tub Clean cycle, or that the cycle is running. On some models it shows as tC followed by L. |
dr | Auto drain (info only) | dr means the washer sat paused or idle for several minutes and is draining the water on its own. |
Cd | Cool down (info only) | On combo models Cd means the drying part finished and the machine is tumbling now and then to keep wrinkles out. It can last up to 4 hours. |
CO1 | Wi-Fi software version (info only) | Shown only in the factory test program. It is the Wi-Fi module's software version, not a fault. |
ED1 | Auto detergent did not dispense | On washers with ezDispense, the detergent level in the reservoir did not go down, usually because old detergent dried and thickened. |
ED2 | Detergent pump circuit open | The board sees an open circuit on the ezDispense detergent pump. |
ED3 | Auto softener did not dispense | The softener level in the ezDispense reservoir did not drop, usually because softener thickened inside. |
ED4 | Softener pump circuit open | The board sees an open circuit on the ezDispense softener pump. |
ED5 | Dispenser board not talking | The main board lost communication with the small board that runs ezDispense. |
OPn | Dispenser drawer open | The washer ran or was started with the detergent drawer not fully closed. |
LOE | Dispenser lid open | The lid on the detergent compartment is open, so washing or drying is blocked. |
IF | Lint filter missing (combo) | On washer and dryer combo models the lint filter is out or not seated, so the dryer side will not start. A magnet in the filter tells a switch it is in place. |
F1 | Drying too hot (combo) | On combo models the drum got too hot because air is not moving well. |
dHE | Dryer heater not heating (combo) | On combo models the drying heater did not raise the temperature as expected. |
LE1 | Drying fan stuck (combo) | The drying fan motor on a combo model is blocked or not responding. |
LE2 | Compressor not running (combo) | On heat pump combo models the compressor is not starting. |
LE3 | Drying blower stuck (combo) | The blower that moves air during drying on a combo model is restricted or locked. |
tE1 | Duct inlet sensor fault (combo) | On heat pump combo models the air duct inlet temperature sensor reads open, shorted or way out of range. |
tE2 | Compressor inlet sensor fault (combo) | The compressor inlet temperature sensor on a heat pump combo reads open, shorted or out of range. |
tE3 | Duct outlet sensor fault (combo) | The duct outlet temperature sensor on a heat pump combo reads open, shorted or out of range. |
tE4 | Evaporator inlet sensor fault (combo) | The evaporator inlet temperature sensor on a heat pump combo reads open, shorted or out of range. |
tE5 | Evaporator outlet sensor fault (combo) | The evaporator outlet temperature sensor on a heat pump combo reads open, shorted or out of range. |
nC / nU | NFC module fault (test mode) | Only shows in the factory test program. The NFC tag module used for phone pairing is open or shorted. |
nE | Wi-Fi module trouble (test mode) | Only shows in the test program. The washer's Wi-Fi module and your router are not talking properly. |
nF | Not connected to Wi-Fi (info only) | Not a fault. The washer has not been linked to your home network yet. It shows only in the test program. |
Tell us the code and model, we usually know the fix before we arrive. Same-day across Orange County.