LG APPLIANCE REPAIR Factory Authorized Service · Irvine, CA

LG Washer Error Codes: What Each Code Means

Most LG washer codes point to something you can check in a few minutes: a clogged pump filter, a closed faucet, a load bunched to one side. The list below covers LG front load washers, including WashTower units and washer and dryer combos. If a code keeps coming back after the simple checks, our factory authorized LG repair technicians can test the part behind it and fix it on the first visit in most cases.

Call (949) 876-7373 Text Us
CodeNameWhat the washer detected
OEWater not draining in timeThe control watched the water level during drain and it did not drop fast enough. Something is slowing the water on its way out, or the pump is not moving it.
IENot enough water coming inThe washer opened its fill valves but the water level barely changed in the time it expected. Usually the supply is weak or blocked, not the machine itself.
UELoad out of balanceThe drum could not even out the clothes before high speed spin, so the washer stopped spinning to protect itself. It happens most with a single heavy item or a tiny load.
UbBalancing in progress (info only)Ub is an information message. The washer noticed an uneven load and is adding water and tumbling to fix it on its own.
uS / u5Vibration sensor problemThe vibration sensor on top of the tub either sent a bad signal or recorded very hard shaking. On a WashTower the sensor sits under the dryer section.
bUHeavy vibration (WashTower)This code shows on some WashTower models when the machine detects shaking far beyond normal. Causes range from a poorly leveled unit to a damaged inner drum.
bEBall sensor (older models)Only washers built around 2006 and earlier have this sensor. It tells the board the tub moved far enough to knock a small ball off its seat, and the board then tries to rebalance.
LEMotor cannot turn the drumThe board tried to spin the direct drive motor and the rotor did not move or the hall sensor did not report the movement.
CEMotor drawing too much currentThe main board saw very high current on the motor circuit. Something is making the motor work far too hard or the motor itself has a fault.
dEDoor not detected as closedThe board does not see the door switch circuit closed, so it will not lock the door or start.
dE1Door switch circuit openSame family as dE. The board is missing the signal that tells it the door is shut.
dE2Door will not lockThe door closes but the lock never confirms it latched, so the cycle does not start.
dE4Door sensor inside lock failedThe door position sensor built into the lock assembly is giving a reading the board does not trust.
PEWater level sensor faultThe pressure sensor that tells the board how much water is in the tub is reading open or shorted, so the washer cannot fill or drain correctly.
FEToo much water in the tubThe water level went above the safe limit. The washer will try to pump it out.
tEWater temperature sensor faultThe board reads the water thermistor as open or shorted, so it cannot control water heating.
AEWater in the base panOn a regular front loader a float switch under the tub found water, so the washer stopped and runs the drain pump. On washer and dryer combo models with a heat pump AE means the compressor is locked.
FFWater or hoses frozenThe washer saw very cold water readings along with a fill, drain or overflow problem, which points to ice in the hoses, valves or pump.
PFPower was interruptedThe washer lost power while it was running. It is an information message, not a part failure.
PSWrong supply voltageThe voltage coming into the washer is outside what it is rated for. Washers expect 120 volts, give or take about 10 percent.
EEControl memory faultThe memory chip on the main board failed its self check.
SudToo many sudsThe washer found too much foam. It adds a suds reducing routine, which can stretch the cycle by about two hours, and may stop the spin to keep suds from leaking out.
CLChild lock is onCL is not a fault. Control lock is active, so every button except Power and the lock button is ignored.
tCLTub Clean reminder (info only)tCL is a reminder that the washer is due for its Tub Clean cycle, or that the cycle is running. On some models it shows as tC followed by L.
drAuto drain (info only)dr means the washer sat paused or idle for several minutes and is draining the water on its own.
CdCool down (info only)On combo models Cd means the drying part finished and the machine is tumbling now and then to keep wrinkles out. It can last up to 4 hours.
CO1Wi-Fi software version (info only)Shown only in the factory test program. It is the Wi-Fi module's software version, not a fault.
ED1Auto detergent did not dispenseOn washers with ezDispense, the detergent level in the reservoir did not go down, usually because old detergent dried and thickened.
ED2Detergent pump circuit openThe board sees an open circuit on the ezDispense detergent pump.
ED3Auto softener did not dispenseThe softener level in the ezDispense reservoir did not drop, usually because softener thickened inside.
ED4Softener pump circuit openThe board sees an open circuit on the ezDispense softener pump.
ED5Dispenser board not talkingThe main board lost communication with the small board that runs ezDispense.
OPnDispenser drawer openThe washer ran or was started with the detergent drawer not fully closed.
LOEDispenser lid openThe lid on the detergent compartment is open, so washing or drying is blocked.
IFLint filter missing (combo)On washer and dryer combo models the lint filter is out or not seated, so the dryer side will not start. A magnet in the filter tells a switch it is in place.
F1Drying too hot (combo)On combo models the drum got too hot because air is not moving well.
dHEDryer heater not heating (combo)On combo models the drying heater did not raise the temperature as expected.
LE1Drying fan stuck (combo)The drying fan motor on a combo model is blocked or not responding.
LE2Compressor not running (combo)On heat pump combo models the compressor is not starting.
LE3Drying blower stuck (combo)The blower that moves air during drying on a combo model is restricted or locked.
tE1Duct inlet sensor fault (combo)On heat pump combo models the air duct inlet temperature sensor reads open, shorted or way out of range.
tE2Compressor inlet sensor fault (combo)The compressor inlet temperature sensor on a heat pump combo reads open, shorted or out of range.
tE3Duct outlet sensor fault (combo)The duct outlet temperature sensor on a heat pump combo reads open, shorted or out of range.
tE4Evaporator inlet sensor fault (combo)The evaporator inlet temperature sensor on a heat pump combo reads open, shorted or out of range.
tE5Evaporator outlet sensor fault (combo)The evaporator outlet temperature sensor on a heat pump combo reads open, shorted or out of range.
nC / nUNFC module fault (test mode)Only shows in the factory test program. The NFC tag module used for phone pairing is open or shorted.
nEWi-Fi module trouble (test mode)Only shows in the test program. The washer's Wi-Fi module and your router are not talking properly.
nFNot connected to Wi-Fi (info only)Not a fault. The washer has not been linked to your home network yet. It shows only in the test program.

Code Keeps Coming Back?

Tell us the code and model, we usually know the fix before we arrive. Same-day across Orange County.

Call (949) 876-7373 Text Us
⚡ $25 OFF For new & referred customers